PLUMBING BASICS: A MUST FOR BATHTUB INSTALLATION

Plumbing Basics: A Must for Bathtub Installation

Plumbing Basics: A Must for Bathtub Installation

Blog Article

Pricing

Each person has got their private rationale on the subject of How to Install a Bathtub.


How to Install a Bathtub Yourself
Setting up a tub isn't precisely brain surgery, yet it does need solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is also a reasonably hard job. If the old bathtub is conveniently obtainable, the job can relocate immediately; if you have to open up a wall to eliminate the old tub and also place the new tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually qualified on your own for the job as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed project, it is much better to consider utilizing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This short article will aid you install a brand-new bathtub in your restroom if you have already bought a brand-new tub and don't require to change the setup of your previous supply of water pipes.
Your devices as well as material checklist should consist of the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be rather problematic as a result of the restricted access that is usually the case.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly come from the pipes. As soon as the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
    Prior to moving on to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipes.
    If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next, place the tap in the placing opening in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in place with the producer provided backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Setting up the Tub


    Utilizing both wooden boards under its feet, place the bath tub in the called for position. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny points.
    The next objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bathtub up until the spirit level reviews level.
    To mount faucets, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the various other tap.
    Activate the water supply as well as examine all joints as well as brand-new pipework for leakages as well as tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the normal electrical outlet for leaks.
    Ultimately, repair the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the tub should wait till the bath tub has actually been utilized at the very least once as this will certainly resolve it into its last position.

    Planning for the Setup


    Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
    Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its last setting.

    Tiling Around the Bathtub


    In the area where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, creating the water to pass through the wall in between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
    You can select from a range of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the tub with water before securing, to permit the motion experienced when the tub remains in use. The sealer can break fairly early if you do not consider this motion before sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    Hopefully you liked our topic about How to Install a Bathtub Yourself. Thanks a lot for taking the time to read our short article. Sharing is nice. Helping people is fun. Thanks for your time. Kindly come by our website back soon.


    Urgent plumbing issue? Connect now.

    Report this page